Tumblelog by Soup.io
Newer posts are loading.
You are at the newest post.
Click here to check if anything new just came in.

November 14 2015

SyntheticGrass3

How to Install an Artificial Grass Lawn



We are best Supply the high quality plastic materials products for Green Roofs, Grass Ground Reinforcement, environmental greening solutions, landscape construction, etc. suppliers,we supply best Supply the high quality plastic materials products for Green Roofs, Grass Ground Reinforcement, environmental greening solutions, landscape construction, etc. products for sale. drainage board

Once you've completed the preparation stage such as measuring how much artificial grass you will need, installing appropriate drainage (if necessary) and removing the natural grass layer, you will end up ready to install your artificial grass lawn. This article outlines the steps you need to follow to help you to complete the task right, from laying the bottom, connecting joints and preventing weed growth.

Lay Gravel Base as well as Sharp Sand

If neccessary, use treated timber/timber stakes to do an area frame. We suggest 4 X Two inches of tantalised treated timber for heavy clay soil areas and poorly draining areas and 2 X 2 inches of tantalised timber permanently draining areas. Screw these timbers for the stakes leaving the stakes on the inside of the perimeter. If the Artificial Grass meet a concrete path, wall or decking, set the timber flush using the surface height and also by using 10mm temporary fillet, pack the timber near to the wall leaving space to enable you to tuck the substitute Grass between the timber along with the adjoining material at the later stage. gravel grid

Squeeze stakes against the inner perimeter timber edging and hammer into the ground ensuring the stakes are slightly below the timber edging. Next screw the timber stake to the timber edging.

With heavy clay soils we advise laying a crushed stone the surface of up to 3 inches. This will likely not be necessary for the majority of areas and only required for those who have a high water table where the ground holds water for a long time of time after it rains. Next compact the bottom using a vibrating plate which can be hired from a machine hire company. Ensure the perimeter is compacted and underneath the timber edging by One inch. Infill the perimeter with sharp sand and level by using a rake. Ensure the sand is level to the peak of the timber edging small again.

For good drainage areas spread a layer of sharp sand to blind in the soil. Next compact the floor using a vibrating plate that could be hired from a tool hire company. Ensure the perimeter is compacted and level with all the timber edging.

Should you put more work in at this stage, your Artificial Grass Lawn will appear better as a result.

Weed Control Layer

Apply the weed control geo textile membrane and cut as necessary. Tack using small 1 " galvanised clout nails to the timber edging. This weed control geo textile membrane prevents any possibility of weed growth through the artificial grass drainage holes.

Unveil Artificial Grass

Lay the Artificial Grass in the desired direction focusing on the carpet and not around the levelled base. Ensure the carpet is put to minimise cuts, joints and waste overlaying the timber edging by the minimum of 4 inches. In the event the artificial grass meets a path or edge, of course, if you have laid the timber edging correctly as previously described, then this artificial grass might be wedged between. If joining, please make sure that the artificial grass is laid with the pile running in the same direction on every piece. Lay the rug on top of the sand in contrast to dragging it across the base material. To help you stop wrinkles or creasing you need to allow 2 to 3 hours to be in before continuing with jointing and adhesive. Cut grass to shape utilizing a sharp Dolphin or Stanley knife or scissors.

Jointing

When jointing your outdoor carpet together, ensure the pile runs inside the same direction. Stop manufacturer's edge strip (if present) and butt two edges together ensuring there won't be any gaps greater than 1mm forwards and backwards carpet edges. The accuracy of this will determine how visible the join is after the completion. Fold back edges and position jointing tape (smooth side down) in order that the edges of the carpet match the tape when joined.

Adhesive

a) Apply the cartridge adhesive in the zig zag motion onto the rougher side of the tape allowing one cartridge for each 3 linear metres. Reject carpet and press both edges in to the wet adhesive, ensuring every bit marries up and has no overlap. Since you are doing this with your fingers, mix the fibres together to conceal the join. Once the whole length is within place and you are very pleased with its appearance it is crucial to walk along the join several times to activate the glue and bond the grass towards the tape. Weigh down the seam to make certain good contact with the glue until it cures. The harder care taken using the operation the neater and tidier the joint is going to be.

or

b) If using the 2-component multi-purpose adhesive, ensure thorough mixing present in components before use. Apply adhesive for the rough side in the tape and spread evenly across a width of at least 20cm using if possible a notched trowel. Sufficient adhesive should be applied so that in the event the artificial grass carpet is pressed in the adhesive, a transfer within the carpet backing is completed. Turn down carpet and press both edges in the wet adhesive, ensuring every piece marries up and has no overlap. Guarantee the carpet does not crest at the seam and is holding flat over the bonded area. After the whole length is within place and you are happy with its appearance it is necessary to walk along the join many times to activate the glue and bond the grass towards the tape. Weight the seam to make sure good contact with the glue until it cures. Greater care taken with all the operation the neater and tidier the joint is going to be.

While you should endeavour to never put adhesive onto the carpet small amounts of glue are easy to remove from the artificial grass fibre using White Spirit along with a small off cut of the artificial grass. Small amounts of cured glue can usually be removed. To prevent situation and the potential for damage to the artificial grass, care and precautions needs to be taken to avoid contact with the fibres constantly.

When the artificial grass has become jointed and glued and you really are happy with the levels screw the grass towards the timber perimeter framework using galvanised screws at least of 12 inch intervals.

Spread Sand (Optional, according to Grass Selected)

Once the artificial grass has become laid use silica sand, that is kiln dried and brush into carpet as you go. Each product would have sand infill but this is simply used to stabilise the rug and at no time if your sand be visible. You should obtain an even spread on the surface using a brush to produce the depth in layers. Tend not to apply the sand in one application. Brush sand into pile just after laying while the artificial grass is dry although weather is good. Brush vigorously contrary to the fibres of the carpet pile to inspire the tufts to stand upright. Putting the correct amount of sand in helps retain the artificial grass to sleep down, protects the fibres and in addition keeps them standing allow it the look of real grass.

After the hard work has been done, it is possible to sit back and relax knowing that your artificial grass lawn will look great and require minimal maintenance.

Contact:
Leiyuan Industrial Company Limited
The nearest air port:Jinjiang Air Port & Xiamen International Air Port
MSN: leiyuan08@hotmail.com
Skype: leiyuan08
+86-595-2278 8697
+86-595-2277 8697
sales08@greening-solution.com
alan@greening-solution.com

Don't be the product, buy the product!

Schweinderl